New torch for Thief 2 that may resemble a torch you have run into in a different Thief game... Now updated to v2, including better texturing, a higher light vhot (so that you can get shadowing off the torch without a light offset), and better detail.

This object is a from-scratch build of an ornate streetlamp for Thief 2. The design is based around triple-housing, cast iron streetlamps found in some areas of St Petersburg, Russia, with the central housing replaced with the Thief 'technomancy' glow ball/particle attachment found on the standard streetlamps.

UPDATED: The download now contains one version of the lamp with two light housings (strlant3.bin), and a version with a single, central housing (strlan4.bin). Follow the instructions in the readme to install the latter, replacing '3's with '4's.

This archive contains models for two and three drawer filing cabinets for Thief 2. The drawers in the objects are jointed, so it is possible to make them open when frobbed, and if the instructions provided are followed it is easy to lock them.

This is a rebuild, reskin, and extension of the Thief street sign model. In addition to a single sign on the post, there are versions of the model with two signs (on opposite sides of the post, and at right angles), three signs, and four signs. See the notes below about texture replacement. Note that, unlike Nameless Voice's street signs, you can not change the angle or height of the signs on the posts: they are fixed at 90 degree intervals and at the same height. This may be sufficient for many situations, but if you need more complicated street signage, look up Nameless Voice's version.

A new turbine object similar to the turbine provided as standard with Thief 2 except with new, better quality texturemaps and 8 sides instead of 6. Virtually the same size as the original (slightly longer). Expect more variations on the theme :) (update: Texture update)

A replacement for the standard Thief/Thief2 compass with individual compass point letters and a bronze/glass centre. I'm not really happy with this, it needs quite a bit of work - expect this to be changed at some point (I should be using the same object name, so you can use this and just replace it with the updated one if/when I do it.)

This is a street lamp model for Thief 2 with a round (6 sides) base and square light housing. This model is virtually the same size as the original strlant object and it requires minimal work to set it up ready for use.

A new electric wall light for Thief 2 in two versions - a low poly version (188 faces) and a high poly version (286 faces). The low poly version has opaque glass while the high poly version has a solid frame, transparent glass and a bulb.

This is a rebuild of the Thief 2 Streetlamp model with a transparent glass lamp housing containing a bulb. This model is virtually the same size as the original and it requires minimal work to set it up ready for use.

This is a rebuild of the Thief 2 Streetlamp model with an octagonal, transparent glass lamp housing containing a bulb. This model is virtually the same size as the original and it requires minimal work to set it up ready for use.

This gas lamp is an alternative to the gas lamps supplied with Thief 2 and it should fit mansion missions rather better than the original. The lamp itself is intended to look somewhat like the lamps in Undying while having rather lower polycounts than the Undying object. It functions exactly like a standard gaslight and should act as a drop-in replacement.

This object a reimplementation of the Thief 2 walspot model providing slightly higher detail than the original for minimal additional cost in polys (for example, the lamp housing is six, rather than five, sided but the extra polys are offset by reduced counts in other areas). The original was used only as a guide for size and this is a complete rebuild of the model required as part of my construction of the triple spot object.

Three spotlights attached to a single base, may be useful in display areas. Provided in two forms: one has the lights angled 18 degrees down from the horizontal, the other has the lights at 45 degrees. This object is based on my reimplementation of the Thief 2 walspot model.

Note that this does not cast three light spots - I haven't checked if it would be possible to get three lights from one object, but I'd be surprised if it was. You need to manually place two spot or omni lights for two of the bulbs!